Peptide Sciences lab tools

Peptide Reconstitution Guide & Concentration Calculator

Calculate the concentration of a reconstituted research peptide and the volume needed for each aliquot, then follow our step-by-step laboratory guide to preparing, handling and storing lyophilized peptides.

Peptide calculator

Laboratory Peptide Concentration Calculator

Choose the peptide quantity in your vial, the volume of solvent you add and the amount of peptide you need in each aliquot. Results update instantly.

1

Peptide quantity in the vialAs printed on the vial label (mg)

mg
2

Solvent volume addedTotal volume of solvent added to the vial (mL)

mL

Enter the volume of solvent you actually add, not the capacity of the solvent bottle.

3

Peptide needed per aliquotAmount of peptide required in each sample (mcg)

mcg

1 mg = 1,000 mcg (micrograms).

This calculator performs unit conversions for laboratory preparation only. Always confirm calculations against your own laboratory protocol. Peptide Sciences Bio products are for research use only.

The basics

What Is Peptide Reconstitution?

Peptide Sciences Bio supplies research peptides as lyophilized (freeze-dried) powder. Lyophilization removes water under vacuum, leaving a dry, stable cake that holds up far better during shipping and storage than a peptide in solution.

Before most laboratory work, that powder needs to be dissolved in a suitable solvent. This process is called reconstitution. Done carefully, it gives you a solution of known concentration, so every aliquot you measure contains a predictable amount of peptide.

The two numbers that matter are simple: how much peptide is in the vial, and how much solvent you add. The calculator above does the rest.

What you'll need

  • Lyophilized peptide vial
  • Appropriate solvent, such as bacteriostatic water
  • Calibrated pipette or measuring device
  • Sterile pipette tips or transfer tools
  • 70% isopropyl alcohol wipes
  • Gloves and standard lab PPE
  • Labels and a marker
  • Refrigerator (2–8°C) or freezer (−20°C)
Step by step

How to Reconstitute a Lyophilized Research Peptide

A standard laboratory procedure for preparing a peptide solution. Follow your institution's protocols and aseptic technique at all times.

  1. 01

    Bring the vial to room temperature

    Remove the vial from cold storage and let it reach room temperature before opening. This limits condensation, which can introduce moisture and affect stability.

  2. 02

    Check the label and COA

    Confirm the peptide, quantity and lot number on the vial label match its Certificate of Analysis. Note the quantity for your calculation.

  3. 03

    Prepare a clean workspace

    Work on a clean surface with gloves. Wipe the vial stopper and the solvent vial stopper with a 70% alcohol wipe and let them air-dry.

  4. 04

    Measure the solvent

    Using a calibrated pipette or measuring device, draw up the exact volume of solvent you entered in the calculator.

  5. 05

    Add the solvent slowly

    Release the solvent gently down the inside wall of the vial, not directly onto the powder. A slow, controlled addition helps prevent foaming and peptide loss.

  6. 06

    Swirl gently; do not shake

    Roll or swirl the vial gently until the powder dissolves. Vigorous shaking can denature or aggregate some peptides. Allow a few minutes if needed.

  7. 07

    Inspect the solution

    A properly reconstituted peptide solution is usually clear. Cloudiness or particles may indicate incomplete dissolution or a solvent mismatch; see "Choosing a solvent" below.

  8. 08

    Label and store

    Label the vial with the peptide, concentration, solvent, date and lot number. Store according to the guidance in the storage section.

Choosing a solvent

Which Solvent Should You Use?

Most research peptides dissolve readily in bacteriostatic or sterile water. Some sequences, especially very hydrophobic or highly charged ones, need a different approach. Always check compatibility with your experimental system.

SolventBest suited forNotes
Bacteriostatic waterMost water-soluble peptides; vials accessed more than onceSterile water with 0.9% benzyl alcohol, which inhibits bacterial growth. Available from Peptide Sciences.
Sterile waterWater-soluble peptides used in a single sessionNo preservative, so intended for single use. Preferred where benzyl alcohol could interfere with an assay.
Dilute acetic acidBasic peptides that resist dissolving in waterA small amount of dilute acid can improve solubility. Dilute further with water once dissolved.
DMSOVery hydrophobic peptides for in-vitro workDissolve in a minimal volume first, then dilute. Check DMSO tolerance in your cell or assay system.
Storage & stability

Storing Lyophilized and Reconstituted Peptides

FormRecommended storageHandling tips
Lyophilized (before reconstitution)−20°C for long-term storage; 2–8°C acceptable short-termKeep sealed, dry and protected from light. Stable at ambient temperature during shipping.
Reconstituted, in use2–8°C (refrigerated)Protect from light. Stability in solution varies by peptide, so prepare only what your work requires.
Reconstituted, longer-termAliquot, then −20°C or −80°CDivide into single-use aliquots so each is thawed only once. Avoid repeated freeze-thaw cycles.
Worked example

How the Peptide Calculation Works

Step 1: Total peptide10 mg = 10,000 mcgA 10 mg vial contains 10,000 micrograms.
Step 2: Concentration10,000 mcg ÷ 2,000 µL = 5 mcg/µLAdding 2 mL (2,000 µL) of solvent gives 5 mg/mL.
Step 3: Aliquot volume250 mcg ÷ 5 mcg/µL = 50 µLEach 250 mcg aliquot is 50 µL (0.05 mL).
Avoid these

Common Reconstitution Mistakes

  • Shaking the vialVigorous agitation can cause foaming, aggregation or degradation. Swirl gently instead.
  • Spraying onto the powderAdding solvent directly onto the cake can scatter powder. Run it down the vial wall.
  • Mixing up mg and mcg1 mg is 1,000 mcg. Unit errors are the most common source of calculation mistakes.
  • Repeated freeze-thawEach cycle can reduce peptide integrity. Store solutions as single-use aliquots.
  • Opening a cold vialCondensation adds moisture. Let vials reach room temperature first.
  • Skipping the labelUnlabeled solutions lead to errors. Record peptide, concentration, date and lot number.
Questions

Peptide Reconstitution FAQ

Need technical help? Contact the Peptide Sciences team.

How do I calculate peptide concentration after reconstitution?

Divide the peptide quantity by the volume of solvent added. For example, 10 mg in 2 mL gives 5 mg/mL, which is 5 mcg per µL. Our peptide calculator does this automatically.

How much solvent should I add to a peptide vial?

It depends on the concentration your protocol requires. Adding less solvent gives a more concentrated solution and smaller aliquot volumes; adding more gives a more dilute solution that is easier to measure accurately in small amounts.

What is the difference between bacteriostatic water and sterile water?

Bacteriostatic water contains 0.9% benzyl alcohol, which inhibits bacterial growth and allows a vial to be accessed more than once. Sterile water has no preservative and is intended for single use.

Why is my reconstituted peptide cloudy?

Cloudiness usually means the peptide hasn't fully dissolved or the solvent isn't well suited to that sequence. Allow more time with gentle swirling, and consider a different solvent for hydrophobic or highly charged peptides.

How should reconstituted peptides be stored?

Keep solutions in use at 2–8°C, protected from light. For longer storage, divide into single-use aliquots and freeze at −20°C or −80°C, avoiding repeated freeze-thaw cycles.

Does Peptide Sciences provide dosing guidance?

No. Peptide Sciences Bio products are sold for laboratory research use only. This guide and calculator cover laboratory preparation and unit conversion, not use in people or animals.

Everything You Need for Your Next Prep

Shop HPLC-MS tested research peptides with lot-linked COAs, and add bacteriostatic water to your order.

All Peptide Sciences Bio products are intended solely for in-vitro research and laboratory experimentation by qualified professionals. They are not drugs, foods, dietary supplements or cosmetics and are not for human or veterinary use. The information and calculator on this page support laboratory preparation only.